Powerdynamo, electronic ignition kit for modified BSA A65

Assembly instructions for ignition kit 74 37 599 00	Version 05.04.2016

If you can install your stock dynamo/alternator and possess basic mechanical skills, you can install a Powerdynamo! If you never have worked on your electrical system, better have it done by someone who knows.
Powerdynamo can not monitor the compliance to those instructions, nor the conditions and methods of installation, operation, usage and maintenance of the system. Improper installation may result in damage to property and possibly even bodily injury. Therefore we assume no responsibility for loss, damage or cost which result from, or are in any way related to, incorrect installation, improper operation, or incorrect use and maintenance. We reserve the right to make changes to the product, technical data or assembly and operating instructions without prior notice.
IMPORTANT:	Designated use This system is designated to replace stock ignition systems in vintage and classic motorcycles whose engine characteristics have not been modified aftermarket. This system is not a tuning system and it will not bring significant increases in engine output. It does however significantly enhance roadworthiness and road safety by offering increased reliability compared with the aging stock systems . As our systems do not tamper with engine characteristics they do not increase emission of gassous pollutants and noise. In most cases emission of pullutants should be even reduced due to better combustion. If used as designated the system therefore will not normally infringe the existing legal status of the motorcycle (this statement is valid for Germany, as this situation might be different in other countries, please consult your local road licencing regulations). This system is not suitable for use in competition events. If used other than designated warranty is voided and it might well be that you do not obtain the desired results. In worst cases use not in accordance with designated use might entail legal roadunworthiness.
	Please read these instructions fully and carefully before starting work on your motorcycle. Please bear in mind that any modification of the material as well as own repair attempts which have not been agreed with Powerdynamo may result in a loss of warranty. Also, please take note of the information provided on the information page for this system. Check that what you have bought really corresponds to the motorcycle you have. Wrong ignition settings may damage your engine and even hurt you during kickstart (violent kickbacks). Be careful during the first test runs. If needed change settings to safer values (less advance).
	Please always use shielded spark plug caps (but not more than 5Kohm) with this system as the hall trigger element is very sensible and may catch the emission of a spark which can lead to ignition disturbances, even failure.
	Never place converter and advance unit (same housing) back to back, even as this might sound convenient. It can result in ignition failure, even destruction of material due to interference
	Our systems are NOT tested for use with other electronic devices (such as GPS, mobile phones, other 3rd party material.) and may cause damage to such parts. Possibly existing electronic tachometers will not work with the new system. Possibly existing safety switches and electronic valve controls are not supported. It might be that your motorcycle was originally equipped with an ignition that did limit top speed for legal reasons. The new system does not have such a facility, so check your legal situation beforehand
	If you have no expertise for the installation have it done by an expert or at a specialist's workshop. Improper installation may damage the new system and your motorcycle.
	If you have access to the Internet, best view those instructions online. You get larger and better pictures by clicking onto them and possibly updated information. System list at http://www.powerdynamo.biz

	You should have received those parts: adapter with double hall sensor magnetrotor (1 magnet, as there are 2 sensor inside the hall element at 135° (rephased version, HS05) or 180° (standard, HS02) advance unit voltage converter 2 x CDI ignition coils HT cables setup wire and small fastening parts

	Place the magnetic rotor onto the crank. It will be fastened there by the stock screw (shorten it or use washers). Add the spring washer supplied. This screw has to position the rotor reliably in its position. Place the hall element onto your engine with 2 screws 2BA (ca 10mm long) Wires facing towards engine first and than exit through the side of the sensor again.

	(simplified picture) The rotor has at first to sit loosely on the shaft, you need adapting its position during timing Now do timing as shown below.

You may consult the wiring described below in graphic form in wire diagram 7412

First, get to know the wires and plugs at the advance unit (labeled 74 00 52).
	Here you have: plug 1 with wires red, white, yellow/black to connect ignition coil 1 plug 2 with wires red, white, red/black and pink to connect ignition coil and temporarily for setup, the setup wire plug 3 with wires white, blue/white and green/red to connect the converter plug 4 with wires yellow/black, red/black, white and red/blue to connect the hall element.' (pictures may be enlarged online by clicking onto them)

Start with connecting the cable from hall-sensor unit to advance unit
	After you have ushered the wires from the hall-sensor through possible tight openings you put the flat 4 hole plug cover onto the wires from the hall sensor. Wire colours remain same. Both plug parts have some elevation to help orientation (we marked them green here for better visibility). Please double check that really colour connects to colour on both sides of the plug connection
	Identify the cable on the advance unit (pos 2 in overview picture) which has a pink wire in it. You have received a cable called setup cable with wires red and white. The plug on this cable matches the plug with the pink wire. When you connect you match. pink with red white with white For setup please connect a battery 6 to 12V (may also be a 9V block as shown here). Red to plus, white to minus. Note: only for systems with negative ground!
	The hall unit shown here free on the table needs surely be fitted onto the distributer at this moment. When you turn the hall rotor - still loosely sitting on the distributer shaft and with the battery connected as described - you will notice that at some point a diode starts shining, than stops doing so until in the next crankshaft revolution, the next does the same. The yellow diode indicates situation on the ignition coil to be fitted on plug one with the wire yellow/black. The red diode indicates situation on the ignition coil to be fitted on plug one with the wire red/black (and pink)

Now you need to set basic timing. For this, the crankshaft has to be in a position in which the piston of the first igniting cylinder is 50 degrees before top dead center (TDC) in 2nd cycle (compression/ignition) Those 50 degrees have nothing to do with any engine advance, they are just some internal reference the system needs. This is valid for both the version for the rephased 90° crank and the normal parallel one. The difference is the arrangement of the hall elements inside the hall unit. The 90° version one is labelled HS05, the parallel one says HS02
	To find those 50° use the new rotor on the crankshaft. You have at this point already installed the new alternator with the rotor nut not fully fastened yet. Bring the piston of 1st cylinder into TDC, 2nd cycle (plugs out). Turn the rotor until its lasered on marking aligns with the left marking on the adapter. Fasten the rotor so that its position can not change itself.
	Than grip the rotor as some knob and turn the shaft clockwise (against engine working direction) until the lased on line aligns with the right marking. You now have the piston 50° BTDC as required for timing.

	With crankshaft in this 50° position of first firing cylinder and pink setup wire connected you slowly turn the hall rotor (sitting loosely on the shaft, do not fasten!) into working direction (anticlockwise) until the yellow diode starts to shine (should the red one shine first, turn on until the yellow starts). Than slowly turn further into same direction until the yellow diode stops shining. In this position (with crank still at the mentioned 50° situation) fasten the hall rotor on the shaft with the central screw and the spring washer to secure it in this position. The ignition coil fitted to the cable which contains a yellow/black wire is the coil which now fires first and the exit of which has to be connected to cylinder number 1 The system now has its basic timing.

	Setting the diverse characteristics (advance in relation to engine revs) is done by setting the 4 small switches in the blue switch block on the advance unit as indicated in the respective instructions.

Take the setup cable off and connect the ignition coils as indicated above.

Now, get to know the cables and plugs at the converter, labeled 7051.
	From the converter box come 3 wire bundles one bundle with a wire red and a wire white having open ends a second with wires red, white. blue/white and green/red ending in a 4hole male plug a third with wires red/green, white and blue/white ending in a female 4hole plug

The cable with the open wires red and white:	is for connection to the battery. Connect the white to minus of the battery and the red to plus of the battery - via the main switch. Include a 5A fuse and always run the wire via the main switch. Otherwise you can not stop the engine and you will drain your battery during longer standstills.

The cable with the male 4 hole plug ...	... you connect to plug 3 of the advance unit. colour matches colour. blue/white to blue/white red to red white to white green/red to green/red

the cable with the female 4 hole socket ...	... remains free (do not connect anything here, cover the plug with tape)
Finally - and before you connect the battery- carefully check again all wiring and fastening. This ignition works with 6 or 12 volts battery (but not without!). It automatically adjusts to the supplied voltage (6 to 12). Should you experience problems, consult our knowledge base.

Finally you will have to activate the appropriate advance line with the DIP switches on the advance unit:

WE would indicate the best setting to you. In this example with switches OFF-ON-OFF-ON as shown left the unit changes from 10° at start to 20° at 1200revs/min and finally 42° at 2200 revs/min - camshaft (for crank double values)

	Important safety and operating information
#	Safety first! Please observe the general health and safety regulations motor vehicle repair (MVR) as well as the safety information and obligations indicated by the manufacturer of your motorcycle. The timing marks on the material are for general guidance only during first installation. Please check after assembly by suitable means (stroboscope) that settings are correct to prevent damage to the engine or possibly even your health. You alone are responsible for the installation and the correctness of settings.
#	Ignition systems generate high tension! With our material right up to 40,000 Volts! This may, if handled carelessly, not only be painful, but outrightly dangerous. Please do keep a safe distance to the electrode of your spark plug and open high tension cables. Should you need to test spark firing, hold the spark plug socket securely with some well insulating material and push it firmly to solid ground of the engine block. Never pull sparkplug caps when engine is running. Wash your vehicle only with engine at standstill and ignition off.
#	Should you have received in the kit HT cables with a fixed rubber boot(which does not contain a resistor) you might have to use spark plugs with an inbuilt resistor (or replace the cap with one containing a resistor) to comply with your local laws.
#	After installation, please check tightness of all screws, even those preinstalled. If parts get loose during run, there will be inevitably damage to the material. We pre-assemble screws only loosely.
#	Give the newly installed system a chance to work, before you start to check and test values, or what is worse apply changes to it. Our parts have been checked before delivery to you. You will not be able to check much anyway. At any rate do refrain from measuring the electronic components (such as ignition coil, regulator and advance unit). You risk severe damage to the inner electronics there. You will not get any tangible results from the operation anyway. Bear in mind that also your carburetor, your spark plugs and spark plug sockets (even if completely new) might be the reason for malfunction. The general experience with our systems is that the carburetor will have to be re-adjusted to lower settings. Should the system not start after assembly, first disconnect the blue (or blue/white) cut-off wire directly at the ignition coil (or in some cases advance unit) to eliminate any malfunction in the cut-off circuitry. Check ground connections carefully, make sure there is a good electrical connection between frame and engine block. In case of troubles, please consult our Knowledge Base first before you send off the material to us for checking
#	The spark of classic, points based ignition systems has with about 10,000 Volts comparatively little energy and looks therefore yellow and fat (which however makes it highly visible). The spark from our system is a high energy spark with up to 40,000 Volts and therefore is needle thin focused in form, and blue in colour, which makes it not so visible. Furthermore you get spark only at kick-start operated speeds and not by pushing the kick-lever down slowly with your hand (as you might get with battery based ignitions).
#	Systems using a twin outlet ignition coils have a few peculiarities. Please observe that during tests on one side, the other has either to be connected to an fitted spark plug or securely earthed/grounded. Otherwise there will be no spark on either side. Also with such open exits long and dangerous sparks may fly all over the coil.
#	Never do electric arc welding on the bike without completely disconnecting all parts containing semiconductors (ignition coil, regulator, advance) stator and rotor need not be taken off. The same is true for soldering. Before touching electronics disconnect the soldering iron from mains! Never use copper putty on spark plugs.
#	Electronics are very sensitive to wrong polarity. After work on the system, do check correct polarity of the battery and the regulator. Wrong polarity creates short circuits and will destroy the regulator, the ignition coil and the advance unit. As a rule, wiring will always be colour to colour. Instances, where colour jumps between wires are expressly mentioned in our instructions.
#	When you handle the new rotor, take care not to damage its magnets. Refrain from direct blows to the circumference of the rotor. When transporting never put the rotor over the stator. Observe our information relative to transport of the material.
#	Do not use spark plug sockets with a resistance of more than 5kOhm. Better use 1 or 2kOhm ones. Bear in mind that spark plug sockets do age and thereby increase their internal resistance. Should an engine start up only when cold, a defective spark plug socket and/or spark plug is very probably the cause. In case of problems check high tension cables too. Never use carbon fibre HT-cables, never use so called "hot wires" which promise to increase spark.
#	It is a good idea to cover the rotor in a thin layer of oil to reduce the risk of corrosion.
#	Never use a claw puller or a hammer to disengage the rotor. Its magnets might become loose in the event. We offer a special puller for disengaging the new rotor again (see assembly instruction)!
#	Should the motorcycle not be in use for some longer period, please disconnect the battery (so existing) to prevent current bleeding through the diodes of the regulator. Though, even a disconnected battery will empty itself after a while.
#	Please do observe these remarks, but at the same time, don't be afraid of the installation process. Remember, that before you, thousands of other customers have successfully installed the system. *Enjoy driving your bike with its new electric heart!*

	Company	Products	Technical Help	Search


	Powerdynamo brings new ignition & light to your vintage motorcycle